Influence of milling parameters on particle size of ulexite material
| dc.authorid | 0000-0002-0159-5953 | en_US |
| dc.contributor.author | Kütük, Sezai | |
| dc.date.accessioned | 2020-05-28T07:28:18Z | |
| dc.date.available | 2020-05-28T07:28:18Z | |
| dc.date.issued | 2016 | |
| dc.department | AÇÜ, Mühendislik Fakültesi | en_US |
| dc.description.abstract | Commercial raw ulexite (U) materials were milled from 0 h to 8 h by using mechanical milling technique for var-ious initial powder size (?3mm;?75?m), ball to powder ratio (5:1; 10:1), and ball size (10 mm; 5 mm). Par-ticle size, morphology, elemental, and crystal structure measurements of the milled powders were performed. Inthe particle size distribution analysis, the smallestd50andd10values were respectively found as 8.846?mand790 nm for U_5m powder (obtained from that initial powder with?3 mm in size was milled by balls with5 mm in size) at 0.5 h. In the morphology analysis, the microstructure of the U_5m powder was observed tobe more homogeneous by means of milling process. In the elemental analysis, it was deduced that the U_5mpowder is not a pure compound. In the crystal structure analysis, it was determined that the crystal structureof the U_5m powder is exponentially deteriorated with increasing the milling time, and then it has become anamorphous structure at the end of 8 h. The crystalline size of the U_5m powder is reduced to 15.5 nm after 4 hof milling. The results of this study are considered to be useful for future nano studies and industrial applicationsof ceramic ulexite compound, which is a boron mineral. | |
| dc.description.sponsorship | Scientific Research Projects Unit of Recep Tayyip Erdogan University: 2014.109.03.01 | en_US |
| dc.identifier.citation | Kütük, S. (2016). Influence of milling parameters on particle size of ulexite material. Powder Technology, 301, 421-428. doi: 10.1016/j.powtec.2016.06.020. | en_US |
| dc.identifier.doi | 10.1016/j.powtec.2016.06.020 | |
| dc.identifier.endpage | 428 | en_US |
| dc.identifier.scopusquality | Q1 | |
| dc.identifier.startpage | 421 | en_US |
| dc.identifier.uri | https://hdl.handle.net/11494/2076 | |
| dc.identifier.volume | 301 | en_US |
| dc.identifier.wosquality | Q2 | |
| dc.indekslendigikaynak | Web of Science | |
| dc.indekslendigikaynak | Scopus | |
| dc.institutionauthor | Kütük, Sezai | |
| dc.language.iso | en | en_US |
| dc.publisher | Elsevier Science BV | en_US |
| dc.relation.ispartof | Powder Technology | |
| dc.relation.publicationcategory | Makale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanı | en_US |
| dc.rights | info:eu-repo/semantics/openAccess | en_US |
| dc.subject | Ulexite | en_US |
| dc.subject | Mechanical milling | en_US |
| dc.subject | Particle size | en_US |
| dc.subject | Morphology | en_US |
| dc.subject | Crystalline size | en_US |
| dc.subject | Nano-sized | en_US |
| dc.title | Influence of milling parameters on particle size of ulexite material | en_US |
| dc.type | Article |
