Design and implementation of a 3D printed RF power transceiver clamp to measure the water level in PVC water pipes

Basit Öğe Kaydı
dc.authorid0000-0003-1859-5236en_US
dc.contributor.authorKasar, Ömer
dc.contributor.authorGeçin, Mustafa Vecdi
dc.contributor.authorGözel, Mahmut Ahmet
dc.date.accessioned2021-04-07T07:47:26Z
dc.date.available2021-04-07T07:47:26Z
dc.date.issued2021
dc.departmentAÇÜ, Mühendislik Fakültesi, Elektrik-Elektronik Mühendisliği Bölümüen_US
dc.description.abstractThere is very few ways to detect the amount of water inside polyvinyl chloride (PVC) pipes without physical intervention. In this study, using additive manufacturing technology, it has been tried to determine the filling rate of water in PVC water pipes with a 3D printed clamp. The fact that the dielectric of distilled water is approximately 80 times that of air has been decisive in the transmission of power from the inner medium of the PVC pipe. In this way, when the amount of water increases in the PVC pipe, the RF power transmission will be decrease depending on level of water inner side of the pipe. The clamp was designed in the f0 = 2.45 GHz ISM band. LC impedance matching was applied to the two ports of the clamp. Thus, higher transmission coefficient was obtained. Used as a near field probe, the clamp was designed to be used horizontally anywhere on the pipe, pluggable. Input power from first port of the clamp is sent to the spectrum analyzer through its second port. The measurement and simulation results show that the transmission coefficient between the ports varies between ?9 dB and ?15 dB according to the selected fill percentages of the pipe.
dc.identifier.citationKasar, Ö., Geçin, M., & Gözel, M. A. Design and implementation of a 3D printed RF power transceiver clamp to measure the water level in PVC water pipes. International Journal of RF and Microwave Computer‐Aided Engineering, e22644.en_US
dc.identifier.doi10.1002/mmce.22644
dc.identifier.scopusqualityQ2
dc.identifier.urihttps://doi.org/10.1002/mmce.22644
dc.identifier.urihttps://hdl.handle.net/11494/2959
dc.identifier.volumeArticle in presen_US
dc.identifier.wosqualityQ3
dc.indekslendigikaynakWeb of Science
dc.indekslendigikaynakScopus
dc.institutionauthorKasar, Ömer
dc.language.isoenen_US
dc.publisherJohn Wiley and Sons Incen_US
dc.relation.ispartofInternational Journal of RF and Microwave Computer-Aided Engineering
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.subject3D printed clampen_US
dc.subjectPF probeen_US
dc.subjectPVC pipeen_US
dc.subjectWater fill rateen_US
dc.titleDesign and implementation of a 3D printed RF power transceiver clamp to measure the water level in PVC water pipesen_US
dc.typeArticle

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
[ X ]
İsim:
omer_kasar.pdf
Boyut:
2.06 MB
Biçim:
Adobe Portable Document Format
Açıklama:
İndir
Lisans paketi
Listeleniyor 1 - 1 / 1
[ X ]
İsim:
license.txt
Boyut:
1.44 KB
Biçim:
Item-specific license agreed upon to submission
Açıklama:
İndir

Koleksiyon

Elektrik - Elektronik Mühendisliği Bölümü Yayın Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu
WoS İndeksli Yayınlar Koleksiyonu